![]() ![]() But I think the information are all there. PS.: some lines have characters pushed far to the right, not sure if it is send by the steam link that way or my putty character formating is wrong. I would be very happy if we can have debian directly installed as I have a few of them stored ). change the controller settings in steam so the controller acts as a gamepad when the Xbox app is launched via big picture. make sure you're 'sharing' your USB connection in the steam link settings for your Xbox 360 controller. install the new beta build on your steam link 6. However you have to give me the exact commands as I am not good with linux. install and run 'Virtual Here' from steam 5. Tell me if you want me to execute or try anything else. freshly unboxed, nothing else done with the steam link yet beside putting in the wifi password. I finally came around to do this, hope this helps. # had errors /mnt/usb/dev didn't exist so make it # The root home is /home/steam, create it to keep env variable clean # Download ArchLinuxArm-armv7 latest rootfs Besides it is straight from the source ) You need to put a single usb stick in that will be overwritten. That didn't work for me so I went with it another way, mostly from here. You will need to reboot after doing this to take affect. The auto power off was really getting to me and the only thing I could find to change that didn't work for me so here is what I did:Īnd all the way to the bottom comment out ![]() All you need to do is get a pendrive and make this file in these folders: /steamlink/config/system/enable_ssh.txt (Note: the file must have some data in it, if enable_ssh.txt is empty it will not work) " password is "steamlink" change your password "passwd" I believe I read it is limited to 8 characters And from there playing with encoder options made the difference."As for enabling ssh on your Steam Link its very easy. So it seemed to be an issue of getting the image from the compter to the pi. Make sure max bitrate is plenty high.įor me I knew my internet connection was decent enough (95mbps), I could see on my computer that my controller had no noticeable delay. Is decoding/encoding causing hangups? Try each encoder option. Is it just the streamed image that seems to be delayed? Is the internet good enough. Is your controller okay? Is it responsive when you use it on the pi not in steamlink?Īre the commands from the pi to your computer good? Try and look at your computer and see if it's responsive when you move the controller. And then try and isolate where the lag seems to be happening. My tips would be make sure you have the performance overlay enabled (Then press F6 to turn it on while using steamlink) and try and understand everything that's being shown. It helped both problems but not as much as I expected or needed.Īny ideas on what I can do now? Where to look next? At my wits end with this. I used to use 5ghz wfi but the lag and stream quality were awful so I got a 50 ft flat cat 6 ethernet cable to run underneath the trim of the wall from the office to the living room. The input lag got a lot better when I changed to gaming mode on the TV, but it's still not usable for shooters. I'm streaming at 2k now since this doesn't make a difference. The video quality is smooth but with frequent periodic moments of stuttering and frame drops regardless of the stream quality, resolution, or bitrate. Normally Moonlight a bit better at higher resolutions but if you don't have NVIDIA you need to setup Sunshine too. Moonlight and Steam Link app on a decent device (I use a Shield normally) both run fantastic with host PC direct connected to a good router. Reducing the graphics quality of the game to medium (I can usually run maxed out without any issues on my PC though) Steam Link HW was good but honestly there's no reason to hunt down the old devices.Increasing the amount of memory allocated to the GPU on the Pi to ~0.5 gb.Enabling all forms of hardware encoding on the host side in the steam link settings.Enabling hardware decoding on the client side in the steam link settings.Tuning the bitrate on the steam link app.Killing Floor 2 is the game I've been using to test my performance.TV is a 4k hisense 65" with "game mode" enabled.Pi is connected directly to the host with a cat 6 ethernet cable and the host is connected to the internet via wifi, but the Pi is not connected to wifi in anyway.Host rig specs are GTX 1080, Ryzen 1800x, 32 gb ram, native 2k resolution, gigabit ethernet controller.The controller is a wired Xbox 360 controller connected to the Pi via USB.Just got the steam link app working on my Raspberry Pi 4 and I am having a lot of input lag when trying to play games and I have no idea where it's coming from, and neither do my friends who all have successful steam link setups (all with different ways of doing it though). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |